Ne namještaš ti i V i W nego biraš jedno od toga dvoje tj ako namjestiš W tada će Vamo sam "namjestiti" napon toliki da prema trenutno korištenom otporu (grijaču) dobiješ željeno ...
Inače o Vamu je bilo možda i najviše pisano samo malo potraži u podforumu "mod" posebno prije cca godinu dana kada je bio nova stvar
Imaš ovu tablicu za orjentaciju viewtopic.php?f=9&t=1386&start=10

Evo stavio na rms mod,i 9w, a ovo imam na 4,5v.
zanima me kako vidim koji je kapacitet baterije

Zanima me i problem,kad stavim na 5v primjer stisnem veliki gumb za parenje i prebaci me na 3,8v zasto

A da ti pročitač VAMO manual da ti ga ja sad ne prepričavam, ne prebaci te nego ti pokaže stanje baterije

_________________
There's a fine line between fishing and just standing on the shore like an idiot. ><((((º>-------------------------------------------



Modovi, akrilni stalci i 3D printanje

Instructions:

1. Press the large button 5 times to turn the unit on

2. Press and hold down the "-"button more than 3 sec to display the Battery voltage

3. Press and hold down the + button more than 3sec,to display the resistance

4. The +/- buttons will change the voltage in 0.1v increments or the Power in 0.5w increments depending on the output setting.

5. Press and hold down the + and - buttons at the same time to enter the Menu. Once in the menu the top right or + button will advance thru the menu and the top left or - button will change that menu setting. There are only 3 function settings in the Menu.


Menu functions:

Menu 1: Hold down both +/- buttons and it enters at Menu 1 and says Power/Voltage. Use the left button to set to either Voltage or Power output. Power output is beneficial in that regardless of your atomizer resistance, the unit will hold constant Power setting for the same vape. You forget about voltage as the unit adjusts that behind the scenes to hold the Power constant.


Menu 2: Once in the Menu by holding +/- buttons advance to menu 2 by pressing the top right or + button. Menu 2 will say LCD Display and then pressing the top left or - button will allow you to switch what is shown on the screen while vaping. You can choose Power(voltage if set from menu 1), Resistance, or Battery. If set to power it will show your setting in Watts (or Voltage if output set to voltage) during vaping. Resistance will show the Atomizer resistance, Battery just shows the current charge of your battery.


Menu 3: Once in menu from holding +/- press top right or + until you get to Menu 3 and it will say LCD On/Off. This menu function just allows you to turn the OLED on or off during vaping


Low Voltage/Short Circuit Protection - display shows "LO-V":

1: Either the batteries need to be charged

2: Vamo short circuit protection kicked in and the head resistance is too low

_________________
There's a fine line between fishing and just standing on the shore like an idiot. ><((((º>-------------------------------------------



Modovi, akrilni stalci i 3D printanje

Max jel ima Vamo mogućnost mjenjanja firmwarea, tj. njegov update?

Sent from my Motorola using Tapatalk2

ne , možeš samo promijeniti cijelu elektroniku
možda ako ideš sve raskopati i programirati ali to je već malo kompliciranije

_________________
There's a fine line between fishing and just standing on the shore like an idiot. ><((((º>-------------------------------------------



Modovi, akrilni stalci i 3D printanje

Tu mogućnost sam vidio samo kod evića,

_________________

MOD: SXK Nebula Zero Mini, Koopor Mini 60W, Cloupor Mini Plus
Atty: Taifun Kayfun Cubis HH.357